Multi-Skilled Engineering Apprentice

Summary

An exciting opportunity to join one of the South East’s leading suppliers of Mechanical and Electrical Engineering Services. A four-year apprenticeship with an in-depth structured training programme based upon the repair of industrial rotating equipment, gaining valuable engineering skills throughout.

Wage

£16,640 for your first year, then could increase depending on your age

National Minimum Wage rate for apprentices

Please note that there are annual incremental increases.

Training course

Engineering maintenance technician - dual discipline (level 3)

Hours

Monday to Friday 07:00 - 15:30 Total hours per week: 40.

40 hours a week

Start date

Tuesday 1 September 2026

Duration

4 years

Positions available

3

Work

Most of your apprenticeship is spent working. You’ll learn on the job by getting hands-on experience.

What you'll do at work

Year one spent full time at IPS (college) and years 2 - 4 spent in each MKE (employer) department, gaining valuable engineering experience and skills from experienced mentors throughout the business.

• Dismantling and reassembly of rotating equipment
• Electrical test and diagnosis
• Mechanical & electrical fault finding
• Rewinding of electric motors
• Dismantling and assembling pumps, motors, gearboxes and fans
• Dismantling, inspecting and assembling bearings and associated systems

Where you'll work

Unit 15b Dolphin Park Upper Field Road
Eurolink Industrial Estate
Sittingbourne
Kent
ME10 3UP

Training

Apprenticeships include time away from working for specialist training. You’ll study to gain professional knowledge and skills.

Training provider

IPS INTERNATIONAL LIMITED

Training course

Engineering maintenance technician - dual discipline (level 3)

What you'll learn

• Review and use information. For example, work instructions, drawings, design specifications, and plant configurations.
• Use planning, prioritising, organising, and time management techniques to plan tasks.
• Identify and organise resources to complete tasks. For example, consumables.
• Respond and adapt to work demands. For example, adapt working methods to reflect changes in working environment, re-prioritise workloads to react to breakdowns and fault scenarios.
• Identify equipment to work on. Check plant configuration is as defined.
• Prepare the work area for maintenance tasks.
• Identify environmental and health and safety hazards and risks and apply control measures.
• Apply health, safety, and environmental procedures in compliance with regulations, standards, and guidance. For example, signage and barriers, working at height, confined spaces, and COSHH.
• Follow security procedures. For example, site access, document classification, and securing assets.
• Follow emergency incident and response procedures.
• Apply sustainability principles. For example, minimising waste.
• Segregate items for reuse, recycling, and waste.
• Use mathematical principles and formulae to support engineering maintenance.
• Apply engineering maintenance standards and procedures.
• Apply foreign material exclusion procedures.
• Follow maintenance tools and equipment control procedures. For example, handling and storage.
• Reinstate the work area.
• Apply team working principles.
• Communicate with others to give and receive information. For example, colleagues, customers, and stakeholders.
• Escalate issues outside limits of responsibility.
• Record information.
• Produce or amend documents. For example, handover notes and reports.
• Identify and highlight issues (red pen), with technical drawings.
• Use digital and information technology. For example, databases, data sharing platforms, email, management information systems, and word processing. Follow cyber security and GDPR requirements.
• Apply continuous improvement techniques to identify improvement suggestions.
• Carry out and record planned and unplanned learning and development activities.
• Electrical and control and instrumentation. Confirm safe electrical isolation lockout tagout method has been applied and test for dead.
• Electrical and control and instrumentation. Select, check, and use electrical maintenance tools, measurement, and test equipment. Select, check, and use control and instrumentation maintenance tools, measurement, and test equipment.
• Electrical and control and instrumentation. Use electrical diagnostic equipment and apply fault finding and rectification techniques. Use control and instrumentation diagnostic equipment and apply fault finding and rectification techniques.
• Electrical and control and instrumentation. Apply problem solving and critical reasoning techniques.
• Electrical and control and instrumentation. Inspect and test electrical aspects of plant. For example, visual checks, insulation and continuity checks, thermographic surveys, and voltage levels.
• Electrical and control and instrumentation. Remove and replace electrical parts.
• Electrical and control and instrumentation. Prepare and terminate electrical cables.
• Electrical and control and instrumentation. Set up and adjust electrical aspects of plant.
• Electrical and control and instrumentation. Clean parts. For example, removal of dust and debris.
• Electrical and control and instrumentation. Conduct and confirm electrical and connected services isolation and deisolation.
• Electrical and control and instrumentation. Conduct functional testing.
• Electrical and control and instrumentation. Inspect and test control and instrumentation systems.
• Electrical and control and instrumentation. Check calibration and make adjustments.
• Electrical and control and instrumentation. Check loop function.
• Electrical and control and instrumentation. Set up and adjust control and instrumentation systems.
• Electrical and control and instrumentation. Remove and replace instruments and sensors.
• Electrical and control and instrumentation. Re-connect instrumentation power supply, cables, pipework, and services.
• Electrical and mechanical. Confirm safe electrical isolation lockout tagout method has been applied and test for dead.
• Electrical and mechanical. Conduct and confirm electrical and connected services isolation and deisolation.
• Electrical and mechanical. Select, check, and use electrical and mechanical maintenance tools, measurement, and test equipment.
• Electrical and mechanical. Use electrical and mechanical diagnostic equipment and apply fault finding and rectification techniques.
• Electrical and mechanical. Apply problem solving and critical reasoning techniques.
• Electrical and mechanical. Inspect and test electrical aspects of plant. For example, visual checks, insulation and continuity checks, thermographic surveys, and voltage levels.
• Electrical and mechanical. Remove and replace electrical parts.
• Electrical and mechanical. Prepare and terminate electrical cables.
• Electrical and mechanical. Set up, align, and adjust electrical aspects of plant.
• Electrical and mechanical. Clean parts. For example, removal of dust and debris.
• Electrical and mechanical. Conduct functional testing.
• Electrical and mechanical. Check condition and operation of mechanical aspects of plant and equipment. For example, pumps.
• Electrical and mechanical. Remove and replace mechanical parts.
• Electrical and mechanical. Examine mechanical parts for defects. For example, pump seals.
• Electrical and mechanical. Set up, align, and adjust mechanical aspects of plant.
• Electrical and mechanical. Lubricate mechanical assemblies.
• Electrical and mechanical. Apply bench fitting techniques.
• Review and use information. For example, work instructions, drawings, design specifications, and plant configurations.
• Use planning, prioritising, organising, and time management techniques to plan tasks.
• Identify and organise resources to complete tasks. For example, consumables.
• Respond and adapt to work demands. For example, adapt working methods to reflect changes in working environment, re-prioritise workloads to react to breakdowns and fault scenarios.
• Identify equipment to work on. Check plant configuration is as defined.
• Prepare the work area for maintenance tasks.
• Identify environmental and health and safety hazards and risks and apply control measures.
• Apply health, safety, and environmental procedures in compliance with regulations, standards, and guidance. For example, signage and barriers, working at height, confined spaces, and COSHH.
• Follow security procedures. For example, site access, document classification, and securing assets.
• Follow emergency incident and response procedures.
• Apply sustainability principles. For example, minimising waste.
• Segregate items for reuse, recycling, and waste.
• Use mathematical principles and formulae to support engineering maintenance.
• Apply engineering maintenance standards and procedures.
• Apply foreign material exclusion procedures.
• Follow maintenance tools and equipment control procedures. For example, handling and storage.
• Reinstate the work area.
• Apply team working principles.
• Communicate with others to give and receive information. For example, colleagues, customers, and stakeholders.
• Escalate issues outside limits of responsibility.
• Record information.
• Produce or amend documents. For example, handover notes and reports.
• Identify and highlight issues (red pen), with technical drawings.
• Use digital and information technology. For example, databases, data sharing platforms, email, management information systems, and word processing. Follow cyber security and GDPR requirements.
• Apply continuous improvement techniques to identify improvement suggestions.
• Carry out and record planned and unplanned learning and development activities.

Training schedule

Maintenance and operations engineering technician Level 3 

Year 1 of the Level 3 Maintenance and Operations Engineering Technician Apprenticeship Standard, the learner will attend four days a week within IPS Rochester workshop, completing practical skills (Performing Engineering Operations) and one day a week studying the Technical Certificate. In Year 2, the apprentice moves to day-release and will attend IPS one day a week to continue the Technical Certificate. Starting in Year 2 and continuing until completion in Year 4. The apprentice will continue to receive regular training and contact with IPS all throughout the programme.

Requirements

Essential qualifications

GCSE in:

English, Maths, IT and Science (grade 4/C and above)

Share if you have other relevant qualifications and industry experience. The apprenticeship can be adjusted to reflect what you already know.

Skills

• Communication skills
• Team working
• Willing to learn
• Practical Skills
• Interest in Engineering

Other requirements

Enrolment onto your apprenticeship programme is subject to prior attainment checks, and your Personal Learning Record will be reviewed upon successful appointment. We are also obligated to follow the guidelines around eligibility, set out by the government apprenticeship funding rules. NB: Please include minimum qualifications (GCSE Maths and English grades) in your apprenticeship application. Tailor your application to the vacancy, dedicating 1-2 paragraphs for each question to demonstrate interest in the role and the company. **If you are unsuccessful, you will be automatically added to our Talentpool list where future vacancies will be sent to you. If you would like to opt out of this mailing list, please select unsubscribe in the email.**